Skip to main content

Convenient Features

1. Automatic/Manual Lock Setting​

Set whether the door locks automatically when closed, or only manually.

Steps (door half-open):

  1. Press Manual Lock button when the deadbolt comes out
  2. Touch the number pad
  3. Enter PIN then press [*] twice
  4. Press [4] for Auto Lock, or [7] for Manual Lock
note

Auto is the default. In Manual mode, the door does not lock automatically — touch the pad or press the Manual Lock button inside.

2. Smart Key Auto/Manual Detection​

Steps:

  1. Touch the number pad
  2. Enter PIN then press [*] twice
  3. Press [1] for Auto, or [3] for Manual
note
  • Auto Mode: place Smart Key on the sensor directly
  • Manual Mode: touch the pad first, then place Smart Key
  • Auto is the default

3. Sound Mute (1-time)​

Mute the operation sound for one use.

Steps:

  1. Touch the pad, then press [*] (in mute state)
  2. Authenticate with PIN or Fingerprint
note

1-time only. Sound returns on the next operation.

4. Sound Volume Setting (7 levels)​

Steps:

  1. Touch the number pad
  2. Enter registered PIN then press [*]
  3. Press [3] to increase, or [6] to decrease
note
  • 7 levels maximum
  • In mute mode, the pad blinks when you press a number
  • Default: high

5. Multi-touch Security​

Adds random digits to your PIN to clear fingerprint residue and prevent PIN exposure.

Steps:

  1. Touch the number pad
  2. Enter PIN then press [*]
  3. Press [5] — melody plays to confirm
  4. Repeat steps 1-3 to disable

:::caution When Multi-touch is enabled After entering your PIN, the keypad shows 3 random digits — press those digits before [*].

  • When Multi-touch is ON → Random Number feature is OFF
  • When Random Number is ON → Multi-touch feature is OFF :::

6. Dual-Mode Security (2nd authentication required)​

After entering your PIN, you must also authenticate with Smart Key or Fingerprint.

Steps (requires PIN + Smart Key/Fingerprint already registered):

  1. Press Register for 5 seconds — all LEDs light, after 3 sec alarm stops, after 2 sec lights up again
  2. Enter current PIN, then press [*] — front panel LED blinks
  3. Press [1] to turn OFF, or [3] to turn ON
  4. When confirmation sound plays, done

How to open the door when Dual-Mode is ON:

  • PIN + Fingerprint, or
  • PIN + Smart Card

:::note Important

  • When in Dual-Mode Security Entry, other buttons are disabled
  • Must complete 2nd authentication within 10 seconds or it times out
  • Guest PIN does NOT require 2nd authentication — enters directly
  • If Guest PIN = User PIN → no 2nd authentication needed
  • 2nd authentication follows the same rules as Successful/Failed Authentication and 1-minute Lock :::

7. Home Network Module & Remote Control (Optional)​

Open the door remotely via Home Network devices or Remote Control (sold separately).

Registration:

  1. Press Registration — beep
  2. Enter PIN then press [*]
  3. Check that [1, 2, 3, 4, 8, 9] are lit on the pad
  4. For Home Network Module press Registration button / For Remote Control press Open button
  5. Press [*] — melody plays, done
note
  • Register additional remotes by repeating step 4
  • Up to 5 remotes

Deletion:

  1. Press Registration for 3 seconds
  2. Enter PIN then press [*]
  3. Check that [1, 2, 3, 4, 8, 9] are lit
  4. Press [0]
  5. Press [*] and hold for 5 seconds — melody plays, done
note

Even if [0] doesn't light in step 3, you can still press it. New remote registration deletes previous ones — this is an alternative deletion method.