Consolidated Manual Rev.09
This manual covers 10 models of EPIC Door Lock. Each model also has its own dedicated page — click the model name to see details.
📋 Models covered
| # | Model | Type |
|---|---|---|
| 1 | ES-S100Dr | RIM |
| 2 | ES-F300Dr | RIM |
| 3 | ES-F301D | RIM |
| 4 | ES-F501D/H | RIM (includes ES-F500D/H, ES-F501D/H, ES-S510D/H) |
| 5 | ES-FF730Gr | GATE |
| 6 | ES-FF731G | GATE |
| 7 | ES-S740D | GATE |
| 8 | ES-F7000Kr | MORTISE |
| 9 | ES-F9000Kr | MORTISE |
| 10 | ES-P8800K | PUSH PULL |
📊 Feature comparison table
| Type | Model | PIN | Card | Fingerprint | Mechanical Key |
|---|---|---|---|---|---|
| RIM | ES-S100Dr | ✅ | ✅ | — | — |
| RIM | ES-F300Dr | ✅ | ✅ | ✅ | — |
| RIM | ES-F301D | ✅ | ✅ | ✅ | — |
| RIM | ES-F500D/H, ES-F501D/H, ES-S510D/H | ✅ | ✅ | ✅ | — |
| GATE | ES-FF730Gr | ✅ | ✅ | ✅ | ✅ |
| GATE | ES-FF731G | ✅ | ✅ | ✅ | ✅ |
| GATE | ES-S740D | ✅ | ✅ | ✅ | ✅ |
| MORTISE | ES-F7000Kr | ✅ | ✅ | ✅ | — |
| MORTISE | ES-F9000Kr | ✅ | ✅ | ✅ | ✅ |
| PUSH PULL | ES-P8800K | ✅ | ✅ | ✅ | — |
🎯 Registration Mode (User)
Press the R (Registration) button on the inner body. The keypad shows LEDs 1-6 and R:
| LED | Mode | Steps |
|---|---|---|
| LED [1] | PIN Number | Enter initial PIN 1234 + [#], enter new PIN → [R] |
| LED [2] | Card (one-by-one) | Enter PIN + [#], place card → [R] |
| LED [3] | Fingerprint (one-by-one) | Enter PIN + [#], place finger 4 times → [R] |
| LED [4] | Guest PIN Number | Enter PIN + [#], enter Guest PIN → [R] |
| LED [5] | Remote Control (one-by-one) | Enter PIN + [#], press OPEN on remote → [R] |
| LED [6] | Face ID (one-by-one) | Enter PIN + [#], stare into camera → [R] |
| R Button | Super Admin PIN | Press OPEN/CLOSE + press R for 10 sec → enter new Super Admin PIN |
🗑 Deletion Mode (User)
Press OPEN/CLOSE for 3 seconds, enter PIN + [#], then select LED:
| LED | Mode | Steps |
|---|---|---|
| LED [2] | Card | All: LED [#] for 5 sec / One-by-one: enter slot + LED [#] |
| LED [3] | Fingerprint | All: LED [#] for 5 sec / One-by-one: enter slot + LED [#] |
| LED [5] | Remote Control | All: LED [#] for 5 sec / One-by-one: enter slot + LED [#] |
| LED [6] | Face ID | All: LED [#] for 5 sec / One-by-one: enter slot + LED [#] |
| R Button | User Registered & Settings Reset | Press OPEN/CLOSE + press R for 10 sec → delete all |
📋 Important notes
- Only 1 PIN can be registered
- Default PIN:
[1, 2, 3, 4] - Registering a new Guest PIN deletes the old one
- Up to 200 cards can be registered
- Up to 100 fingerprints can be registered
- Up to 30 faces can be registered
- Additional authentication (Card/Fingerprint/Remote/Face) does NOT delete the primary authentication (PIN)
- If primary authentication (PIN) is not registered, dual authentication cannot be set
- If an error occurs during registration, LED [2] will blink
- If the Remote Control receiver module is not connected, LED [5] won't light up → cannot register/delete remotes
:::warning Professional installation required This product must be installed by a qualified technician only. Do not install outdoor or in direct weather. :::
📖 Original PDF manual: epic.co.kr